No-one likes general adverts, and ours hadn't been updated for ages, so we're having a clear-out and a change round to make the new ones useful to you. These new adverts bring in a small amount to help pay for the board and keep it free for you to use, so please do use them whenever you can, Let our links help you find great books on glass or a new piece for your collection. Thank you for supporting the Board.

Author Topic: Help Please to ID this old Cut Glass  (Read 883 times)

0 Members and 1 Guest are viewing this topic.

Offline mhgcgolfclub

  • Members
  • **
  • Posts: 1700
Help Please to ID this old Cut Glass
« on: July 04, 2021, 10:36:26 AM »
Help please to ID this old glass, I think its a drinking glass and not a Jelly.
It has a grey tinge and sliced panels and weighs 350gm

Height 138mm, diameter of rim 99mm and base 83mm
A nice yellow glow under uv light.
Wear to base.

Thanks Roy

Support the Glass Message Board by finding a book via book-seek.com


Offline Paul S.

  • Members
  • **
  • Posts: 9938
  • Gender: Male
Re: Help Please to ID this old Cut Glass
« Reply #1 on: July 04, 2021, 11:36:09 AM »
would agree Roy, probably not a jelly  -  despite that it has what is sometimes described as a 'pan topped' bowl - sweet meats often had such a bowl design.         I could be very wrong, but seem to vaguely recall that a yellow glow might mean selenium, but not sure.     Regret can't see from you picture of the underside of the foot what it is we're supposed to be seeing  -  presumably it has a polished depression where the scar was removed - try raking the light.          How about it's for champers?             When you say ID  -  you are never going to know the maker - did you mean to say age? ;D           What is the ring like when flicked?

Support the Glass Message Board by finding glass through glass-seek.com


Offline mhgcgolfclub

  • Members
  • **
  • Posts: 1700
Re: Help Please to ID this old Cut Glass
« Reply #2 on: July 04, 2021, 02:56:27 PM »
Thanks Paul for your reply.

I think I was just showing the narrow ring of wear on the base. Has quite a  nice ring when flicked, and your correct I would be interested in the age that it may be.

Roy

Support the Glass Message Board by finding a book via book-seek.com


Offline Paul S.

  • Members
  • **
  • Posts: 9938
  • Gender: Male
Re: Help Please to ID this old Cut Glass
« Reply #3 on: July 04, 2021, 03:13:01 PM »
Roy  -  so there isn't any polished depression where the pontil scar would have been ground/polished out  -   and if you don't have a shears mark either then assume it's a machine finished base so age very unlikely to be before 1900 do you think and probably some time after too.

Support the Glass Message Board by finding glass through glass-seek.com


Offline mhgcgolfclub

  • Members
  • **
  • Posts: 1700
Re: Help Please to ID this old Cut Glass
« Reply #4 on: July 06, 2021, 05:35:40 PM »
Thanks Paul your most likely right again , its no big deal I rather have my good health back again.

Thanks for all your help Roy

Support the Glass Message Board by finding a book via book-seek.com


Offline mhgcgolfclub

  • Members
  • **
  • Posts: 1700
Re: Help Please to ID this old Cut Glass
« Reply #5 on: January 02, 2022, 11:03:54 AM »
Just looking at the glass again I should of said there is quite a large polished depression where the pontil mark was ground out.

Roy

Support the Glass Message Board by finding glass through glass-seek.com


 

SMF spam blocked by CleanTalk
Visit the Glass Encyclopedia
link to glass encyclopedia
Visit the Online Glass Museum
link to glass museum


This website is provided by Angela Bowey, PO Box 113, Paihia 0247, New Zealand